FSX & SLI

[Black ZR-1]

It boot me to safemode with a warning message: "Warning! Change CPU or Memory Frequency in CMOS"

There were some settings I could not change though. They were:

PCIE Spread Spectrum: Default. I could not select it. By default it was set to Disabled.

LTD Spread Spectrum: Center Spread. This feature was not available for me to select.

Chipset Voltage Core: 4.1 V. Only settings it could let me select were 1.4 & 1.5.

Vcore: 1.35. It had a lot of variables but 1.35 was not there. The closest was 1.3250 & 1.3375. I set it to 1.3250 since you said not to exceed 1.35.

Cpu Clock Ratio: 7x. This feature was not available.

Hyperthreading: Enabled. This feature was not available, but I remember seeing it before I flashed my Bios to 1001.

Adressing Mode: 1T. Only options it gave me were 1 clock & 2 clock.

The rest of the settings it accepted.

I have not changed the NEW FSB: 1233 or NEW MEM SPEED: 616 yet because I figured I would let you know first.

Standing by..

[Nick N]

[quote]It boot me to safemode with a warning message: "Warning! Change CPU or Memory Frequency in CMOS"

There were some settings I could not change though. They were:

PCIE Spread Spectrum: Default. I could not select it. By default it was set to Disabled.

LTD Spread Spectrum: Center Spread. This feature was not available for me to select.

Chipset Voltage Core: 4.1 V. Only settings it could let me select were 1.4 & 1.5.

Vcore: 1.35. It had a lot of variables but 1.35 was not there. The closest was 1.3250 & 1.3375. I set it to 1.3250 since you said not to exceed 1.35.

Cpu Clock Ratio: 7x. This feature was not available.

Hyperthreading: Enabled. This feature was not available, but I remember seeing it before I flashed my Bios to 1001.

Adressing Mode: 1T. Only options it gave me were 1 clock & 2 clock.

The rest of the settings it accepted.

I have not changed the NEW FSB: 1233 or NEW MEM SPEED: 616 yet because I figured I would let you know first.

Standing by..

[Black ZR-1]

It boot me into safemode so I set everything back to default settings.

[Nick N]

[quote]It boot me into safemode so I set everything back to default settings.

[Nick N]

E6300 does not have hyperthread technology


duhhhhhhhh    ;D    

I forgot

[Black ZR-1]

I'm alive and kicking!

Vcore: 1.4 exactly set in Bios

New FSB: 333

New Mem: 667











CPU TEMP & VOLTAGE

[Nick N]

I'm alive and kicking!

Vcore: 1.4 exactly set in Bios

New FSB: 333

New Mem: 667











CPU TEMP & VOLTAGE

We are still not right here... looking at this now..

[Nick N]

Strange.,.. perhaps my first assesment was correct about FSB and the reason you did not boot was because of the vcore.

Lets leave that for a moment

Notice the Vcore in CPUz.

With a setting of 1.4v, it reads 1.344 which is low. That falls in line with the information I got about the voltage regulator on this board.

I want you to enter the BIOS and raise that to 1.45 and then re-boot. If the Vcore in DCPUz reads 1.38 or less, leave it at 1.45v in the BIOS

Post back about that while I do some checking on this BIOS and how it reads FSB properly.

Lets get the Vcore strait first

[Black ZR-1]

Set Vcore to 1.45

[Nick N]

Set Vcore to 1.45

OK.. I can live with that for now.

Give me just a minute

[Nick N]

Set Vcore to 1.45

The board is doing something strange and I am not sure exactly what is going on.. but, lets try this:


NEW FSB: 1233

[Black ZR-1]

[quote]



The board is doing something strange and I am not sure exactly what is going on.. but, lets try this:


NEW FSB: 1233

[Nick N]

[quote][quote]



The board is doing something strange and I am not sure exactly what is going on.. but, lets try this:


NEW FSB: 1233

[Black ZR-1]

[Nick N]

EDIT: I noticed my Vcore is starting to fluctuate between 1.38 - 1.39

Thats exactly where I want the vcore to sit right now