Angel Aircraft

Anything to do with Aircraft Design, FSDS, G Max, Aircraft Animator, SDL Edit, etc. Novice or skilled - stop here & learn!

Angel Aircraft

Postby Travis » Mon Sep 29, 2008 12:18 am

I've been creating a model of the Angel Aircraft for FS9.  I have the model nearly complete, but I can't seem to get the flight dynamics to work properly.

I used AirWrench to create the airfile, using the information found here and in this PDF.

Every time I start it, I can't seem to get it into the air.  It gets up to speed, but the nose stays glued to the ground.  The only way I can get it to fly is to slew it up in the air and then apply massive elevator trim.

What could be the cause? :(
Image
User avatar
Travis
Major
Major
 
Posts: 4381
Joined: Thu Feb 06, 2003 3:17 am
Location: KAUS - 30 MI NW

Re: Angel Aircraft

Postby Felix/FFDS » Wed Oct 01, 2008 5:45 pm

Remember to check your e-mail for the link to the photos I took!!
Felix/FFDS
User avatar
Felix/FFDS
Administrator
Administrator
 
Posts: 16776435
Joined: Wed Jan 31, 2001 9:42 am
Location: Orlando, FL

Re: Angel Aircraft

Postby Brett_Henderson » Sat Oct 04, 2008 6:08 am

The trick to getting these new model to fly correctly, is to start with accurate numbers and geometry.

It sounds like your control surface placement, and size... and your CoG might be off.
Brett_Henderson
Major
Major
 
Posts: 3403
Joined: Fri Oct 08, 2004 7:09 am

Re: Angel Aircraft

Postby Milton » Sun Oct 05, 2008 10:11 am

Brett is on it.

Also, go here http://pagesperso-orange.fr/hsors/index.html and download AFSD for more help on seeing exactly what your numbers are.

Verify that your main gear placement is correct relative to CoG, and that CoG (fuel tank locations especially at/near 0,0,0) is at 25% MAC.

Then ensure your engines placement is at or near CoG vertically. i.e. +n, +-n, 0  like this:

Engine.0 = 7.5, -6.5, 0.0
Engine.1 = 7.5, 6.5, 0.0

If your thrustline is above CoG, it will cause a nose down moment.  A small nose down moment may be preferable but that can be achieved with +.1" to +1" placement.  If engines are well above CoG, you may experience what you have now.
Milton
Dash 7, Aero Commanders, Howard 500, D18S, Spartan, XP47J, Beechcraft A28 (Grizzly)
User avatar
Milton
1st Lieutenant
1st Lieutenant
 
Posts: 352
Joined: Tue Jun 04, 2002 1:52 am
Location: USA - NM

Re: Angel Aircraft

Postby Travis » Sun Oct 05, 2008 5:05 pm

Thanks for all the help, folks.

I've finally gotten it flying correctly, and I have the textures about 25% done.  I should have a beta model between the middle of the month and Halloween, depending on panel stuff and gauges.

Any other help is very much welcome.

Oh, and I got those shots, Felix.  Very nice!  They really helped with details of the aircraft.
Image
User avatar
Travis
Major
Major
 
Posts: 4381
Joined: Thu Feb 06, 2003 3:17 am
Location: KAUS - 30 MI NW

Re: Angel Aircraft

Postby sall » Wed Oct 29, 2008 9:48 pm

The Angel was certified FAR Part 23 in the USA by the Federal Aviation Administration (FAA) in late 1992. Angel Aircraft throw out extremely hot flares that attract heat-seeking missiles away from the engines of the aircraft. It was started by Carl Mortenson, a pilot and aircraft mechanic with 50 years of aviation experience.
--------------------
Sally
Link Building
sall
Ground hog
Ground hog
 
Posts: 1
Joined: Wed Oct 29, 2008 10:19 pm


Return to Aircraft & 3D Design

Who is online

Users browsing this forum: No registered users and 211 guests