elevation on save

FSSC, Airport 2.*, CfgEdit, etc. Get to grips with designing Scenery & Panels here!

elevation on save

Postby jgattico » Fri May 12, 2006 3:59 pm

I have created a helipad on top of a building.  I flew to it and landed.  I saved it the flight so I could start from there.
But when I start the flight again I am on the ground not the helipad.  The Helipad is above me.
jgattico
Ground hog
Ground hog
 
Posts: 19
Joined: Mon Apr 10, 2006 9:08 pm

Re: elevation on save

Postby Travis » Fri May 12, 2006 4:23 pm

Lots of info missing, here.  We need more if we're gonna point you in the right direction.

First off, what modelling program did you use to make the thing?

Secondly, did you use an object placer program, and if so, which?
Image
User avatar
Travis
Major
Major
 
Posts: 4381
Joined: Thu Feb 06, 2003 3:17 am
Location: KAUS - 30 MI NW

Re: elevation on save

Postby jgattico » Wed May 17, 2006 7:25 am

I used Runway12 to place and create the helipad.  I used AFW for the building
jgattico
Ground hog
Ground hog
 
Posts: 19
Joined: Mon Apr 10, 2006 9:08 pm

Re: elevation on save

Postby Travis » Wed May 17, 2006 10:27 am

Okay, first, to narrow down what the problem is, try placing that exact same helipad somewhere close by on the ground and saving the flight there.  If you end up starting on the ground again, your problem is with Rwy 12 and its miriad finicky moments.  If you wind up starting CONSISTENTLY on top of the pad, your problem is with Airport.

Let us know.
Image
User avatar
Travis
Major
Major
 
Posts: 4381
Joined: Thu Feb 06, 2003 3:17 am
Location: KAUS - 30 MI NW

Re: elevation on save

Postby jgattico » Wed May 17, 2006 9:19 pm

I put the helipad on the ground and landed on it.  Then saved the flight.  went back and was the copter was on the ground in the middle of the pad.  I also put a pad about 10 ft up but just droped through it.
JOhn
jgattico
Ground hog
Ground hog
 
Posts: 19
Joined: Mon Apr 10, 2006 9:08 pm

Re: elevation on save

Postby Travis » Wed May 17, 2006 9:53 pm

Are you using FS8 or 9?  I had this problem in FS8 several times, with scenery that had elevated landing pads or runways.  I don't know if its a problem in FS9 or not.  I haven't encountered it, but I haven't been using any elevated platforms yet.
Image
User avatar
Travis
Major
Major
 
Posts: 4381
Joined: Thu Feb 06, 2003 3:17 am
Location: KAUS - 30 MI NW

Re: elevation on save

Postby jgattico » Thu May 18, 2006 5:25 am

FS9
jgattico
Ground hog
Ground hog
 
Posts: 19
Joined: Mon Apr 10, 2006 9:08 pm

Re: elevation on save

Postby garymbuska » Fri May 19, 2006 7:58 am

 Is your crash detection turned off when you land on the object? That could be your problem if so as fs will allow you to land on any surface even water if crash detect is turned off so when you save the flight and restart it you will wind up starting under water or under the object you landed on as fs thinks the object is a non landable object in the case of water sea planes are able to land on it by setting a flag in the air file that allows it to land on water where other craft do not have this flag and will crash. I do not know if there is a solution to your problem you may have to define it as some other object other than a raised platform i would suggest you try to find a building that allows you to use it as a starting point and find out what makes it that way.
Problaly some simple little flag or something you have overlooked. 8)
Gary M Buska
SYSTEM Specs ASUS P8Z68 V/GEN 3 mother board: INTELL I7 2600k 3.48 ghz Quad core CPU with Sandy bridge: 12 Gigs of 1800hz ram:
GTX 950 OVER CLOCKED: 2 Gigs Ram Windows 10 Home 64 bit Operating system. 750W Dedicated modular power supply. Two Internal 1TB hard drives 1 External 1TB 3.2 USB hard drive. SAITEK Cessna flight Yoke with throttles.
CH Rudder Peddles 27 inch Wide screen Monitor
User avatar
garymbuska
Major
Major
 
Posts: 4415
Joined: Tue Dec 30, 2003 11:10 am
Location: Jacksonville, Florida


Return to Scenery & Panel Design

Who is online

Users browsing this forum: No registered users and 115 guests