Page 1 of 1

Flatten, and create runway utility, for FS 2002..?

PostPosted: Thu Dec 18, 2003 2:12 pm
by Fozzer
Hi All... 8)....!
Can you lead me to a simple, (very simple!), FS 2002 utility to flatten* a selected area and create a hard/grass/dirt runway ready to accept LAGO's FSSE objects.
An example would be to create a Bush, etc,  runway where one does not at present exist.

(Chuck Dome has one on page 4 of Sim V Scenery Design Utilities, but it's for FS5, FS'98, CFS and FS 2002, and I don't know if it will work for the later FS 2002/FS 2004 series...)...?
Many thanks... ;)...!

Cheers all... ;D...!
Paul.

* ...if possible, and also remove any existing objects, (default trees, buildings, etc.).

Re: Flatten, and create runway utility, for FS 200

PostPosted: Thu Dec 18, 2003 2:17 pm
by Hagar
Hi Foz. I've told you many times before - try FSSC. ::)
http://fssc.avsim.net/

Flattening an area & removing default objects with FSSC is not difficult once you understand the basics. When you get used to it you might find that you don't need FSSE. :P ;)

Re: Flatten, and create runway utility, for FS 200

PostPosted: Thu Dec 18, 2003 2:37 pm
by Fozzer
Ta Doug... ;D...!
Just downloaded it. Will give it a try, but it's got to be simple... ;)...!
..Oh...
...and I'll still continue to use FSSE, just to annoy you, if nothing else... ;D...!
..together with my FS Navigator... ;)...!
(I love all this Payware "stuff"...).... ;D... ;D... ;D...!
Tee-Hee...!

Cheers mate... ;D...!
Paul.

Re: Flatten, and create runway utility, for FS 200

PostPosted: Fri Dec 19, 2003 2:33 pm
by Fozzer
Do you know what...?
Remember I said "Simple*"...?
Well I fiddled and far*ed around with FSSC to create a simple* runway until my eyes bled.... :'(...!
I created the xx.bgl file for my desired location, stuck it in my scenery folder, flew to the site....
...nuffin'... ::)...!
So I downloaded Chuck Dome's excellent, (simple*!), little program, (436K), and the whole thing worked an absolute treat.... ;D.... ;D... ;D...!
Choice of Tarmac with numbers, grass, concrete or dirt.
All done in 30 seconds... ;D...!

http://www.simviation.com/fsdesign_scenery4.htm

..an example of my little site with it's FSSE objects and it's new grass runway...
...lubbly-jubbly... ;D...!

Point Reyes:

Image

Cheers all...!
Paul.

*I love the word "Simple". It often goes with the word "Quick"... ;)...!

Re: Flatten, and create runway utility, for FS 200

PostPosted: Fri Dec 19, 2003 3:16 pm
by Hagar
Well done old bean. ;D

It does look a handy little utility at that.
As I've said many times - it's a matter of preference so try all possible alternatives & judge for yourself. What suits me obviously won't suit everyone. I find FSSC simplicity itself. ;)

Re: Flatten, and create runway utility, for FS 200

PostPosted: Fri Dec 19, 2003 4:56 pm
by RollerBall
Hmmm

Nice little spot for a stop-over

You must let me know what the ATC and ILS fequencies are some time Foz ;D

And presumably there is an NDB there so vistors who don't know where it is can find it 8)

Re: Flatten, and create runway utility, for FS 200

PostPosted: Fri Dec 19, 2003 6:00 pm
by Fozzer
Hmmm

Nice little spot for a stop-over

You must let me know what the ATC and ILS fequencies are some time Foz ;D

And presumably there is an NDB there so vistors who don't know where it is can find it 8)


Hi Roger...
Leave San Francisco International.
Tune to Sausalito VOR 116.20.
Pass over.
Re-tune to Point Reyes VOR 113.70.
Fly there.
Fozzers Point Reyes airstrip. Bearing:
N 038* 03.34'
W 122* 57.22'
Watch out for sailing boat masts if flying in low, heading 270 degrees.

Tea and bacon sarnies are on me at the FBO... ;D...!

Cheers... ;)...!
Paul.